復合中的氣泡現象

Bubble phenomenon in recombination

1．薄膜潤濕不良，應提高膠的濃度和涂布量，MST、KPT表面不易濕潤，易產生氣泡，特別在冬天。油墨上的氣泡，用提高膠的用量的方法去除。

1. If the film is poorly wetted, the adhesive concentration and coating amount should be increased. The surface of MST and KPT is not easy to be wetted and is easy to produce bubbles, especially in winter. The bubbles on the ink can be removed by increasing the amount of glue.

2．油墨表面凹凸和起泡，應把復合膜的復合溫度和復合壓力提高。

2. If the ink surface is concave and convex and blistering, the composite temperature and pressure of the composite film should be increased.

3．油墨表面上的膠涂布量少，應增加復合輥的壓貼時間及使用光滑輥筒、薄膜預熱充分、降低復合速度、選擇濕潤性好的膠以及正確選用油墨。

3. The amount of glue coating on the ink surface is small, so it is necessary to increase the pressing time of the composite roller and use the smooth roller, fully preheat the film, reduce the composite speed, select the glue with good wettability and correctly select the ink.

4．薄膜中的添加劑（潤滑劑、抗靜電劑）被膠滲透，應選用分子量高、固化迅速的膠，提高膠濃度，提高烘箱溫度充分使膠干燥，不使用超過3個月存放期的薄膜，因為電暈處理已喪失。

4. When the additives (lubricant, antistatic agent) in the film are penetrated by the glue, the glue with high molecular weight and rapid curing should be selected, the glue concentration should be increased, the oven temperature should be raised to fully dry the glue, and the film with a storage period of more than 3 months should not be used, because the corona treatment has been lost.

5．冬天里氣溫低，粘結劑對薄膜和油墨轉移，潤濕粘附效果不好，故操作場所保持一定溫度。

5. In winter, the temperature is low, and the adhesive transfer to the film and ink, and the wetting and adhesion effect is not good, so the operating site should maintain a certain temperature.

6．干燥溫度太高，發生膠的起泡或表皮結皮，內里不干，應調整膠干燥溫度。

6. If the drying temperature is too high, blistering or skin scaling of the glue occurs, and the inside is not dry, the drying temperature of the glue should be adjusted.

7．濟南復合袋中的復合輥薄膜間夾帶入空氣，應提高復合輥溫度，減小復合角（薄膜厚、硬時易產生氣泡）。

7. Air is entrained between the film of the composite roll in Jinan composite bag. The temperature of the composite roll should be increased to reduce the composite angle (bubbles are easy to occur when the film is thick and hard).

8．由于薄膜阻隔性高，膠固化時產生的CO2氣體，殘留在復合膜中，未印刷處也有氣泡，應提高固化劑量，使膠在干燥中固化。

8. Due to the high barrier property of the film, the CO2 gas generated during the curing of the adhesive remains in the composite film and there are bubbles at the unprinted part. The curing dose should be increased to make the adhesive solidify in the dry.

9．膠中的脂酸乙酯是油墨粘結料的良好溶劑，膠溶滲了油墨，只在油墨上有氣泡，應避免水分滲入膠中及提高膠干燥溫度，減少對油墨的溶滲。

9. The ethyl fatty acid in the glue is a good solvent for the ink binder. The glue dissolves the ink and only bubbles on the ink. It is necessary to avoid water infiltration into the glue and increase the drying temperature of the glue to reduce the penetration of the ink.

復合袋生產期間出現復合氣泡的原因以及應對如上，希望給您好的幫助，不管是生產還是使用都應做好了解事項，關注我們http://www.673338.com.cn為您講解更多事項！

The causes of compound bubbles during the production of composite bags and the countermeasures are as above. I hope to give you good help. Whether it is production or use, we should do a good job in understanding matters and pay attention to us http://www.673338.com.cn Tell you more!