Some plastic self sealing bags get a blind hole after forming, and then drill through. This method is suitable for thin and deep holes, which can prevent the core from deforming during forming. Plastic products have no holes after forming, and then the holes will be processed again. The latter two knife methods are limited to a few easy cutting materials, such as nylon. At the same time, it needs secondary processing. The production efficiency is low, and it is difficult to guarantee the quality of fine holes, so it is rarely used. This section mainly introduces the design principle and processing method of holes directly generated during forming.

對在成型時直接生成的孔，無論伺種類型，均應設置在不易削弱制品強度的部位，且孔的形狀應力求不使模具制造工藝復雜化。是在成型的制品殘留熔接痕和削弱強度的重要因素。周?chē)O(shè)一個凸邊來加強。同時，孔與孔的間距及幾到制品邊緣的距離也要適當。所示的尺寸關系確定，當兩個孔不一“樣大小時，按小7L取值；熱塑性塑料自封袋的注塑制品按表2—7中數值的75％取恒。對于孔的深度，不同類型的孔的深度因成型方法的不同而不同。通孔注塑制品L的通扎用得很多，成型通孔用的型芯一般有以門L種安裝辦法。

For the holes directly generated during forming, regardless of the type, they should be set at the parts that are not easy to weaken the strength of the products, and the shape of the holes should strive not to complicate the mold manufacturing process. It is an important factor for residual weld lines and weakening strength of formed products. Set a convex edge around to strengthen. At the same time, the distance between holes and the edge of the product should also be appropriate. The dimension relationship shown is determined. When two holes are different in size, the value is taken as 7L smaller; the injection molded products of thermoplastic self sealing bags are taken as 75% of the values in table 2-7. For the depth of holes, the depth of different types of holes varies with different molding methods. Through hole injection molded products L are used a lot, and the cores used for forming through holes generally have l installation methods.

內一端固定的型芯來成型，且易生成飛邊，當型芯較細時易彎曲。這種固定型芯的方法不能成型深孔。由兩個兩端固定的則芯來成型，由于將一個型芯設計得比另一個大o．5—1mm左右，保證孔的同心度，不于引起安裝和使用土的困難，而且增加了型芯的穩定性，孔的精度低。由一端固定，一端導向支撐的型芯來成型，這樣型芯有較好的強度和剛度，又能保證同心度，但導向部分易因?qū)蛘`差磨損而產生圓弧溢料。以上無論采用何種固定方法，孔的深度均不能太大，公則型芯會彎曲。通常九探隨塑料流動性的4(同而不同，流動性好的塑料自封袋的7L的深度可以達到10倍孔徑，流動性中等的不能超過7倍孔徑，而流動性差的塑料制品的孔深小于4倍7L徑；否則只能采取機械加工的力法獲得。

It is easy to produce flash and bend when the core is thin. This method of fixing the core cannot form deep holes. It is formed by two cores fixed at both ends. Because one core is designed to be about 0.5-1mm larger than the other, the concentricity of the hole is guaranteed, which will not cause difficulties in installation and use of soil, but also increase the stability of the core, and the accuracy of the hole is low. It is formed by the core with one end fixed and one end guided and supported, so that the core has better strength and stiffness and can ensure concentricity, but the guide part is easy to produce arc overflow due to the wear of guide error. No matter what fixing method is adopted above, the depth of the hole should not be too large, and the core will be bent. Generally, the depth of 7L of plastic self sealing bag with good fluidity can reach 10 times the aperture, and that of plastic products with medium fluidity can not exceed 7 times the aperture, while that of plastic products with poor fluidity is less than 4 times the 7L diameter; otherwise, it can only be obtained by mechanical processing.

以上就是為大家介紹的有關濟南自封袋的詳細的介紹,希望對您有所幫助.如果您有什么疑問的話,歡迎聯系我們.我們將以的態度,為您提供服務.http://www.673338.com.cn

The above is a detailed introduction about Jinan self sealing bag. I hope it will help you If you have any questions, please contact us We will provide you with professional service http://www.673338.com.cn